Puppeteer

Author Topic: SR2 starter replacement  (Read 13060 times)

KC7NOA

  • Jr. Member
  • **
  • Posts: 93
    • View Profile
Re: SR2 starter replacement
« Reply #30 on: February 19, 2022, 09:15:30 PM »


Diesel Engineering

  • Jr. Member
  • **
  • Posts: 59
    • View Profile
Re: SR2 starter replacement
« Reply #31 on: February 20, 2022, 01:19:13 AM »
The spacer you have is for the 24 volt coaxial starter. For the starter in the photo you would need the thinner spacer. At a guess I would say it is around 1/2 inch thick.

KC7NOA

  • Jr. Member
  • **
  • Posts: 93
    • View Profile
Re: SR2 starter replacement
« Reply #32 on: February 20, 2022, 04:15:29 AM »
24v ... I was trying 12v on the original.

Know a part number of the spacer I should be looking for?


Diesel Engineering

  • Jr. Member
  • **
  • Posts: 59
    • View Profile
Re: SR2 starter replacement
« Reply #33 on: February 20, 2022, 05:43:52 AM »
The Lister part number for the thinner spacer is 202-26550

broncodriver99

  • Sr. Member
  • ****
  • Posts: 477
    • View Profile
Re: SR2 starter replacement
« Reply #34 on: February 20, 2022, 07:48:16 AM »
Just a stupid yet obvious question. Have you tried your local starter/alternator rewinder? There may not be one in your area but here luckily there are still a couple of old school shops capable of rewinding a starter. May be worth pulling out the phone book and seeing if you have a local rewind shop. Even if worst case they can't fix it maybe point you in the right direction.
« Last Edit: February 20, 2022, 07:50:02 AM by broncodriver99 »

KC7NOA

  • Jr. Member
  • **
  • Posts: 93
    • View Profile
Re: SR2 starter replacement
« Reply #35 on: February 20, 2022, 08:13:40 PM »
It's not the winding that is a problem ... I think the magnetic field has degraded ... the gear is half way out and does not retract from the flywheel.

The starter had probably been overheated and collapsed the power in the alinco magnet.

cobbadog

  • Hero Member
  • *****
  • Posts: 1051
    • View Profile
Re: SR2 starter replacement
« Reply #36 on: February 26, 2022, 10:13:13 AM »
2 options in my book, re-instate the magnetic field as you would re-charge a magneto or take you spacer to a machine shop and have it milled down to size.
Coopernook - the centre of our Universe.

KC7NOA

  • Jr. Member
  • **
  • Posts: 93
    • View Profile
Re: SR2 starter replacement
« Reply #37 on: March 01, 2022, 08:49:10 AM »

well,

Gary sent me a spacer along with a rocker push rod .. the spacer does not fit my housing -- just slightly bigger. The spacer fits the starter nicely ...

I took the original starter to a shop  -- the owner is 85yrs old and recognized the numbers as a starter from a boat. I'm like, yea .,.. that's a big possibility.
So he said he will return it look and operating like new -- good to me !!!

Honestly, i don't like not having sources for wear parts ... i have no idea how long ago this starter failed -- or why. I hope i can source a spacer for this china clone ...

sirpedrosa

  • Hero Member
  • *****
  • Posts: 863
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
Re: SR2 starter replacement
« Reply #38 on: March 01, 2022, 03:36:08 PM »
KC7

go easy. there is nothing that cant be done. Off course it ill coast, but you aim to get it running. Be patient, sort all out to the best solution you can get.

Cheers
VP
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

cobbadog

  • Hero Member
  • *****
  • Posts: 1051
    • View Profile
Re: SR2 starter replacement
« Reply #39 on: March 02, 2022, 06:08:47 AM »
Im back home and have found a manual of sorts but I need to find out how to compress it enough to post on the forum
Coopernook - the centre of our Universe.

Hugh Conway

  • Hero Member
  • *****
  • Posts: 529
    • View Profile
Re: SR2 starter replacement
« Reply #40 on: March 02, 2022, 10:01:11 PM »
@cobbadog
Looking at the manual you provided, I was reminded of a boat I used to have circa 1973.
It had an SR2 rated at 12BHP continuous. On the side of the fuel control was a stop with a lead seal. Breaking the seal allowed the operator to advance the throttle to "WAR EMERGENCY POWER" I never tried that, but the engine could produce that 12 HP effortlessly. The heated air could be ducted to the cockpit and sure kept it warm.
Cheers
Hugh
JKson 6/1  (Utterpower PMG ) Off-grid
Lister 6/1 Start-O-Matic engine......running with PMG
1978 Royal Enfield (glutton for punishment by Indian iron)
1963 BMW R-27 project

cobbadog

  • Hero Member
  • *****
  • Posts: 1051
    • View Profile
Re: SR2 starter replacement
« Reply #41 on: March 03, 2022, 04:52:55 AM »
Nice bit of info there Hugh, It is amazing what can be found out on these Forums.

Will try to load another 2 manuals but one in each post in case it over loads the system
Coopernook - the centre of our Universe.

cobbadog

  • Hero Member
  • *****
  • Posts: 1051
    • View Profile
Re: SR2 starter replacement
« Reply #42 on: March 03, 2022, 04:56:13 AM »
Sorry the last one I have was titled A25 Lister Air Cooled but must be too large a file.
Coopernook - the centre of our Universe.

dax021

  • Full Member
  • ***
  • Posts: 220
    • View Profile
Re: SR2 starter replacement
« Reply #43 on: March 03, 2022, 05:58:30 PM »
@cobbadog
Looking at the manual you provided, I was reminded of a boat I used to have circa 1973.
It had an SR2 rated at 12BHP continuous. On the side of the fuel control was a stop with a lead seal. Breaking the seal allowed the operator to advance the throttle to "WAR EMERGENCY POWER" I never tried that, but the engine could produce that 12 HP effortlessly. The heated air could be ducted to the cockpit and sure kept it warm.
Cheers
Hugh

Apparently Spitfires had a seal like that too.  Break the seal for emergency HP.  Hence the saying "through the wire"  If the plane came home with the wire broken, the engine had to stripped and rebuilt, which apparently pissed off the techies.

cobbadog

  • Hero Member
  • *****
  • Posts: 1051
    • View Profile
Re: SR2 starter replacement
« Reply #44 on: March 04, 2022, 05:03:05 AM »
Even more great information. Some Techies are just like big sheilas and whinging about anything that makes them do something for a change.
Coopernook - the centre of our Universe.