Author Topic: PETTER - PAZ1 - New project  (Read 66781 times)

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
PETTER - PAZ1 - New project - Gantry legs get primary paint
« Reply #180 on: April 23, 2021, 10:21:06 PM »
Hi Gentles

After a while out, Im back again... just to show crane legs with primary paint.

Stay safe.
VP

PS: manage to do for first time gun painting... not bad for a noob.
« Last Edit: April 23, 2021, 10:24:36 PM by sirpedrosa »
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
PETTER - PAZ1 - New project - tweaking the hilux time belt and IP
« Reply #181 on: April 23, 2021, 11:19:19 PM »
Hi Gentles

My apologies to not share in last post some TLC to my latest acquisition, a Hilux 1992, that needed to tweak the injection pump (spill time was set a beat early, making it to sound a dry knock).

To pull out crank pulley I made some basic tools from "NASA's" plans, in order to reach the timing belt.

A few pics to enjoy...

VP
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
PETTER - PAZ1 - New project - Gantry crane is done and aproved
« Reply #182 on: June 06, 2021, 09:38:56 PM »
Hi Gentles

Gantry crane is done, and aproved.... by wife.

It only needs to be tested with the desired load limit!.

Cheers
VP
« Last Edit: June 07, 2021, 01:48:15 PM by sirpedrosa »
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

BruceM

  • Hero Member
  • *****
  • Posts: 3068
    • View Profile
Re: PETTER - PAZ1 - New project
« Reply #183 on: June 07, 2021, 01:03:32 AM »
Nicely done!  The swing for testing adds scale; It's big!


sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
PETTER - PAZ1 - Question for all members - gear pumps
« Reply #184 on: October 03, 2021, 09:37:12 PM »
Hi Gentles

Please give me some lights here: Im wondering to make a simple log splitter with one of these Petters.

But for this task I need some help, this site (https://www.dieselworldmag.com/diesel-engines/petter-paz1-diesel-engines) states that the "peak torque value of 11 lbs-ft occurred at 1500 rpm".

That said, I need to know what kind of hydraulic pump I need (Im looking for a 2 stage, due to its way of work, specialy in low pressure) in order this engine can go with it (I think I need also some sort of rpm multiplier)

So please be my guests to give all help needed.

Cheers
VP
« Last Edit: October 03, 2021, 09:39:23 PM by sirpedrosa »
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
PETTER - PAZ1 - A business card of a friend
« Reply #185 on: March 15, 2022, 08:58:06 PM »
Hi Gentles

I was leafing through some papers and I found a business card of a friend.

I think lots of members had him as friend too.

Cheers
VP
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
Re: PETTER - PAZ1 - New project - wiring AVR to alternator
« Reply #186 on: September 18, 2023, 09:20:11 PM »
Gentles, Bob

Bob give a hand here please.

Pay atention to my reply here: https://listerengine.com/smf/index.php?topic=8333.msg102277#msg102277

Now I want to put the AVR in to get power as stable as possible.

Windings look like the sketch below. And the AVR is a cheap one.

How should I connect it to make it right!

Cheers
VP
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

ajaffa1

  • Hero Member
  • *****
  • Posts: 1790
    • View Profile
Re: PETTER - PAZ1 - New project
« Reply #187 on: April 18, 2024, 09:34:52 AM »
Hi VP, I had a look at this and did some research today. That AVR is not suitable for what you have, it requires six wires and your diagram only shows four. There are some more suitable four wire  AVRs available on Ebay search for GAVR, some require a 9 volt battery to initialise them.

Bob

dax021

  • Full Member
  • ***
  • Posts: 237
    • View Profile
Re: PETTER - PAZ1 - New project
« Reply #188 on: April 18, 2024, 06:21:32 PM »
I haven't seen a post from VP for a while now.  I hope's ok and will be back soon.

ajaffa1

  • Hero Member
  • *****
  • Posts: 1790
    • View Profile
Re: PETTER - PAZ1 - New project
« Reply #189 on: April 18, 2024, 10:17:44 PM »
My Wife tells me he has been unwell and spent some time in hospital. I`m sure we all wish him a speedy recovery.

Bob

dax021

  • Full Member
  • ***
  • Posts: 237
    • View Profile
Re: PETTER - PAZ1 - New project
« Reply #190 on: April 19, 2024, 09:08:56 AM »
Thanks Bob, yes sure hope he gets better soon and starts posting again.

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
Re: PETTER - PAZ1 - New project - Give a run to all
« Reply #191 on: June 14, 2024, 12:31:29 AM »
Gentles,

Many thanks to all members, and enthusiasts for kind words.

Today was a county holiday here, and so I give a run to all stationary (well, the Bernard is not a pure stationary, and the Volvo Penta stayed cold, but you all understand).

The Lister still being the swiss clock, off course, and both Petters needed to be primed, and the German is ready to roll.

And... its time to restore a 2 stroke 50cc motorcycle, from 1990, of my passed away oncle, that I buyed from my cousin, just to stay busy.  ;D ;D ;D

A few pics to showoff.

Cheers
VP

PS: Stef its not a Zündap, because its too expensive, but this one is also an icon from the old days.
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

BruceM

  • Hero Member
  • *****
  • Posts: 3068
    • View Profile
Re: PETTER - PAZ1 - New project
« Reply #192 on: June 14, 2024, 01:02:20 AM »
What a beautiful photo of your recently restored engines! 
I look forward to seeing your progress on the 50cc motorcycle as well.
Best Wishes,
Bruce

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
Re: PETTER - PAZ1 - New project - Making a decent kart to put gen
« Reply #193 on: September 24, 2024, 10:00:18 AM »
Gentles

Dont miss me, Im bad news.  ;D ;D ;D ;D

Nonetheless, thing are not halted.

The first Petter is - finnaly - going on a decent kart to run the Winpower geny.

Here are some pics to show.

Cheers
VP
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).

sirpedrosa

  • Hero Member
  • *****
  • Posts: 888
  • 21NOV2019 - Finally I hear that sound... again
    • View Profile
Re: PETTER - PAZ1 - New project - Fancy handle
« Reply #194 on: September 25, 2024, 12:04:29 AM »
Gentles

Another fancy handle to pull the kart.

pic to showoff

Cheers
VP
By order of firing up:
Bernard 18A - 1968 (mama's water pump - year of my birth)
Petter PAZ1 - Jun 1967, 3HP, sn 416xxxx
Petter PAZ1 - Nov 1979, 3HP, sn 425xxxx
Lister 12/2 - 12651227, the pearl!
Deutz MAH 914, 1952 - Zündfix in chamber and go (7Mai2023).