Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - KC7NOA

Pages: 1 2 3 [4] 5 6 7
46
Engines / Re: SR2 starter replacement
« on: April 20, 2022, 05:43:15 PM »
Iv bought some metric and sae Allen wrenches and 1/8th slips and 9/64 does not fit ....

What am I looking for?

47
Engines / Re: SR2 starter replacement
« on: April 19, 2022, 06:18:16 PM »
I see how your saposed to pull this apart ...

Yep, some idiot put this on backwards ...


48
Engines / Re: SR2 starter replacement
« on: April 18, 2022, 09:04:25 PM »
do what you have done already and loosen all those bolts at the rear of the belt pulley to see if that section will move forward leaving the flat section on the shaft then there should be a nut holding the flat section in place and possibly on a keyway.

There is a allen screw that goes into the keyway... iv not loosened it yet ..

49
Engines / Re: SR2 starter replacement
« on: April 18, 2022, 08:12:16 PM »
Yes, they will contact the snout ... there is about a 1/4" clearance between hub and bolt heads -- just under

Yes, that is a taper lock pulley. There should be two threaded holes in the hub face that can be used to jack the pulley off of the sheave with bolts. The problem is someone has installed that pulley and sheave backwards so it is likely going to be difficult to get it apart. The bolts should be facing out so it can be serviced. Do the bolts in the pulley contact the snout on the generator if you back them out?

50
Engines / Re: SR2 starter replacement
« on: April 18, 2022, 03:19:57 PM »
I dont see much ...


51
Engines / Re: SR2 starter replacement
« on: April 17, 2022, 09:08:18 PM »
Not much yet ...

I think they hold and squeeze two halves together and grab the shaft ... as well as has a keyway...

I pried on the back ... ie , pushing twards the right .. only bending the heads some ...


52
Engines / Re: SR2 starter replacement
« on: April 17, 2022, 02:25:03 PM »



53
Engines / Re: SR2 starter replacement
« on: April 17, 2022, 02:19:25 PM »
Sigh

54
Engines / Re: SR2 starter replacement
« on: April 17, 2022, 01:58:10 PM »
Ok, ... I don't want to break this ... but how does this come off


https://imgur.com/xYbVO9v

55
Engines / Re: SR2 starter replacement
« on: April 15, 2022, 04:32:35 PM »
On to the probable next problem ... I think this gen head needs new bearings... the tag is very faded ... any ideas?

[img]https://imgur.com/NZGsQeo[img]
https://imgur.com/NZGsQeo

56
Engines / Re: SR2 starter replacement
« on: April 12, 2022, 08:56:21 PM »
Should add ...

Replacing the pushrod was easy ... with valve up ... push valve down by hand .. while holding valve down push the pushrod off to one side, replace doing reverse order ... check lash and adjust if needed

My second cylinder was not firing from a fuel leak ...the compression nut at the injector/pipe/tube was loose ... letting fuel spray into oil .. turned almost 4 complete revolutions before it was tight ... seems like injector is ok

57
Engines / Re: SR2 starter replacement
« on: April 12, 2022, 08:50:48 PM »
Does this sound normal?
Or mains/wrist needing replaced?

https://youtu.be/3QayhMV03cM

58
Engines / Re: SR2 starter replacement
« on: April 09, 2022, 11:10:33 AM »
https://youtube.com/shorts/6Aq6KDARAfM?feature=share


[url]https://youtube.com/shorts/6Aq6KDARAfM?feature=share/[url]

59
Engines / Re: SR2 starter replacement
« on: April 09, 2022, 11:03:05 AM »
Finally got the broken stud replaced and the original starter installed ...
[img]https://youtube.com/shorts/6Aq6KDARAfM?feature=share/[img]
[url]https://youtube.com/shorts/6Aq6KDARAfM?feature=share/[url]
Video probably does not work

60
Engines / Re: SR2 starter replacement
« on: March 11, 2022, 09:58:13 AM »
I have a 3/8" hammer drill ... and i can buy a set or reverse drill bits locally .. i seen them on the shelf behind the maned parts desk ...

Iv done this kind of work before with a magDrill .. but i no longer have access to that kind of equipment

Pages: 1 2 3 [4] 5 6 7