Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - oldtime

Pages: [1]
1
General Discussion / Lister JP3 16KVA 3 phase generator .
« on: February 21, 2022, 10:01:26 PM »
Hi all anyone got any leads on a manual for the 3 phase Generator ?
 Its all painted Army green !! It starts and runs Well . I need to sort out the Generator end . thanks Mark Canberra Australia

2
Everything else / JP Lister Fuel Drain
« on: February 21, 2022, 01:23:41 AM »
Hi all how does this water drain work ?
 Genuine lister JP3 with generator   16 KVA three phase
 I am also looking for information about the Generator end .
 It has been under a house for the last 20 odd years .
 Got it home on the weekend its Very heavy thinking above two tons .

3
Listeroid Engines / lister JP3 filter mod
« on: May 07, 2019, 11:43:11 PM »
Hi all I have seen a couple of fuel filter mods for the original Cast iron fuel filter .
 I want to know what fuel filter people are using . I can do the machining but cant find a suitable filter .
 My local filter place was a total waste of time . thanks to all

4
Listeroid Engines / ajaffa Bob OK ?
« on: May 03, 2019, 07:17:07 AM »
Hi all is Bob ok ? I have been trying to contact him . He has been in Hospital .

5
Listeroid Engines / JP3 engine dating ?
« on: April 26, 2019, 08:27:50 AM »
Hi all more questions !!!!
Engine no 60 40 255.
27 3 35 specification
Any idea when it was made . Does anyone know how to decide these numbers thanks to all

6
Listeroid Engines / Jp3 inspection !!!
« on: April 21, 2019, 07:16:16 AM »
Hi all slowly getting it to bits .  It's looking much better .. but
I have found a loose crankshaft timing gear . I did not want to take out the crankshaft but it looks like it will have to come out to fix the timing gear I suspect it will have a worn out key . Not looking forward to getting it out . I only have one shoulder that works properly .  I am thinking of remove flywheel and putting it on it's end and pulling out the crankshaft with the forklift . It's big and ugly .  What do you think about this . 

7
Listeroid Engines / Ozlisteroids.
« on: April 16, 2019, 11:08:34 AM »
Hi all I have used them a few times . A real nice guy. Is he still going ? Hope is ok . Anyone got a phone number for him .. thanks to all

8
Listeroid Engines / Jp cylinder liners
« on: April 13, 2019, 09:41:52 AM »
Hi all anyone know the difference in liners from a cs and a jp
 I can get cs liners. But not had any luck getting some for the jp . It's getting cleaner .. have the heads off . The liners might go again . There is lots of carbon . So much the valves are not seating . The ports are full .. not sure why . Time will tell
 

9
Listeroid Engines / Jp3 oil quantity
« on: April 10, 2019, 06:51:10 AM »
Hi all anyone have an idea how much oil is in a jp3 ? The industrial version ? I have found the plug near the oil pump . I am not looking forward to pulling the plug. . there looks like a big mess coming up .

10
Listeroid Engines / Hi I am new here .
« on: April 06, 2019, 03:35:32 AM »
Greetings from Australia .
Yes I have rusty metal syndrome .....
Just finished a ronaldson and tippet ck twn cylinder 27 hp diesel .. now for my next project . Lister JP3 !  It's a bit sad but will endavour to put a smile back on .  It's an industrial engine . It will require a few bits .  Liners and pistons maybe .  I am still assessing the bits .  I might c it I can use some listeroid liners but will c .  Thank God I have a machine shop . It's going to need some help . I have been scraping the oil of the outside looking for the sump plug !  Still looking . Got to there somewhere !!! Anyway back to the filth hellow to all

Pages: [1]