Puppeteer

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - maxx123

Pages: [1]
1
Waste Vegetable Oil / Re: Washing
« on: March 28, 2015, 08:37:50 PM »
running a wvo boiler to heat the house. tried water filtering last summer  found that spraying water on top of the oil was the best ..if you stir it up too much you get white  crap that need to be unloaded in to the neighbors yard.

seems the water loves to grab onto  glycerin  and settle .

boiler in on youtube   veggie boiler

2
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: July 21, 2014, 02:35:54 PM »
Thanks for the response  . All is good have the proper ecumenicaland picked up electronic hand throttle
I really like it much better then the old governor style . Very consistent in speed.
hook this up to anything ..
with the consistent  rpm running a generator would be much better under a load.

 

3
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: March 10, 2014, 11:25:18 PM »
Had the ev80 running found that there are three bleeding bolts to remove air pockets in the cooling system 

4
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: March 09, 2014, 02:53:58 PM »
Blue,

All diesels  running at 3600 rpm are loud,  if you saw the video .it was running between 400 rpm and 1300 . this is a exact knock off of the yanmar 2V78  like the Yanmar L100  is the same as the Chinese 186 engines

parts are available.

 This motor can be used for anything , motorcycle,boat, garden tractor shit even a generator you can have it run a smaller head at 1800 rpm even 1500 rpm..

Also this engine weight is 56 kg for 20 hp that is light


5
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: March 09, 2014, 01:49:32 PM »
 Here is the ev80  being tested

http://www.youtube.com/watch?v=VuhxeLGIX18


6
Changfa Engines / Re: Need help with parts for s195
« on: March 08, 2014, 04:23:22 PM »
Piston? do you also need rings set? head gasket, 
I can get for you

were are you located

7
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: March 08, 2014, 04:21:15 PM »
Been dealing with John at haige , had the  ecu controller and wiring harness for a generator  3600 rpm.. they resent proper  ecu and wiring harness for a variable speed control.

it can be controlled by a foot pedal, I modified the wiring to handle a hand controller.   

there seems to be no service manual for this . I am using a Yanmar 2v78 manual. this motor is 100% copy.. except horizonal . the electronic wiring I have been figuring out the wiring codes, hope to have for requests , only left with the 3 pin diagnostic to figure out

will be posting engine running on youtube  today , ev80 diesel 

really sweet sound 

8
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: August 25, 2013, 10:03:35 PM »
startamatic, can you email me maxx123@hotmail
 


I know the stepper motor only travels about an inch   with the ecu    so getting a pulse controller to adjust it.  or the Y- manufacture of the ecu and controller I am unable to find anything about them ..


thx

9
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: June 05, 2013, 10:03:24 PM »
Yes it is the same add.

Maxx

10
Changfa Engines / Re: ChangChai all aluminum EV 80
« on: May 23, 2013, 01:08:24 PM »
Hello I Just received 4 -EV 80 engines here in Eastern Ontario  I,ve put them on kijiji   really nicely built units. been translating a german repair  manual into English.   Of course I ordered extra parts basic stuff ,fuel filters,oil,air, injector nozzles .. also working on a modified wiring for the electronic actuator. fly by wire  throttle.. 

Pages: [1]