Puppeteer

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - chefiam1

Pages: [1]
1
Engines / Re: head temp sensor
« on: January 17, 2020, 11:29:58 AM »
now since i pulled the cht out puting it back it needs to be grounded.
so what type of sealant should i use on cht threads so it seals and still stays grounded. or will it be grounded enough just using any thread sealant?
                                                     thanks, chefiam

2
Engines / Re: head temp sensor
« on: January 17, 2020, 11:22:53 AM »
Snowman, that is exactly what i have !! could not figure out how the temp sensor
and oil were connected along with the fuel shut off. i thought i had a bad cht but , that stays n/c then when the temp reaches a certain point it opens and cut the fuel off. did i get it right snowman? thanks again.

                                                       chefiam1

3
Engines / head temp sensor
« on: January 15, 2020, 04:29:55 PM »
Chef here again, where would i get a drawing  of how to wire the sensor up.
two wires cannot be that hard. what i have it shows it going to the oil pressure switch but,i don't have an oil pressure switch. unless they both are inside the temp sensor?all help is welcomed. building the motor had directions. now i'm
stuck on little things that has become big thinks! i would like to start this machine i guess it's called patience!!

                                                 thanks, chefiam

4
Lister Based Generators / Re: TL2 location on block for lock pin
« on: November 24, 2019, 06:28:03 PM »
I meant TDC

5
Lister Based Generators / TL2 location on block for lock pin
« on: November 24, 2019, 06:23:48 PM »
my work manual does not tell or show where the hole to put lock pin in to lock TDS?
any help is appreciated.i'm probably looking right at it

                                                         thanks

6
Engines / valve job
« on: September 14, 2019, 02:04:39 PM »
it needs a valve job  valve inserts,valve guides ect. i have all the new parts.
so when i send it to the machine shop should i send it in pieces or put it together
with the old parts and let them take it apart? the cost of doing the valve job is 200.00
with a turn around in a week i thought that was reasonable

7
Engines / how to set the engine up
« on: September 14, 2019, 12:13:34 PM »
whatis the best way to work on a TL2 lister motor. the manual has it sitting
with the fan side down or can they be put on a engine stand? what is the best way.

                                                       thanks

8
Engines / cylinders
« on: September 14, 2019, 04:40:40 AM »
i took the tl2 motor back from a mechanic that said he could not find parts. it was all in pieces.
now i have a problem there are no marks on the cylinders for position and number. i'm new at this
maybe someone can lead me in the right direction.

                                                            thanks

9
Engines / tl2 piston
« on: September 08, 2019, 01:53:12 PM »
after taking carbon off top of piston i noticed valve marks and pitting
should i replace it ?

10
General Discussion / Lister TL2 has a 16" fan
« on: August 27, 2019, 01:07:39 PM »
I have a TL2 and it has a fan on the main shaft, and mine is broken .so, i'm
looking for a replacement . the factory says the TL2 does't have a 16" fan. so,
i'm sort of lost

11
General Discussion / lister TL2
« on: August 19, 2019, 03:38:14 AM »
new to the forum .i have a TL2 that was brought to me in 2 box  ive. sorted things out and have a large
parts list nothing big alot of bolts and things like that are missing.iv'e breifly dealt with a uk distributor
but, i was wondering if there is a large parts house stateside? east coast perferrably.FPA

Pages: [1]