ALL SOLD

The spares are sold pending funds, so that package deal is null and void. The new package deal includes the engine, Winco 4KW gen head assy, radiator assy, and the 12V power supply. I plan to disassemble it to put it all on a small pallet for shipment. You can have the wood 4x6 beams too, but it will likely be cheaper to leave them out of the shipment.

Edited to change quantities of sold items.

Here is a list of the parts that go with the engine that I am selling. Almost all came from Central Maine Diesel. I will sell these parts separately, and adjust the engine price accordingly. Prices are per each except where noted + shipping at cost. I only ship to the USA. No fee payment methods: PayPal F&F, Venmo, Cryptocurrency. Payment +3% methods: PayPal G&S, credit/debit via phone.

YouTube video of parts:
https://www.youtube.com/watch?v=iLtxAADOYRg

3 con rod small end brg, std $15
4 con rod large end brg set w/shims, std $15
3 main brg, sleeve type, std $25 ea.
3 bronze idler gear $120
3 injector, Bosch, complete $70
3 injector pump, Bosch $75
4 gib key set (2) $10
1 gib key puller $50
3 injector nozzle, Bosch $30
3 pump element, Bosch $30
3 pump valve, Bosch $20
3 valve guide set (2) $12
3 valve set (2) $17
3 valve spring set (4) $13
3 rocker arm set (2) $13
1 SOLD rocker arm assy $30
3 2 tappet set $20
1 SOLD wrench set $20
4 3 banjo bolt set (2) $10
1 injector pump tappet $15
3 idler gear bolt $8
2 valve guide seal set (2) $10
2 valve cap set (2) $5
4 valve cup set (2) $5
3 piston w/ wrist pin, std. $40
3 2 piston ring set, std $20
1 cylinder block w/ liner, std. $150
2 cylinder block w/o liner $75
1 head stud set w/nuts $40
2 1 camshaft assy. w/gear $80
2 cylinder liner $75
2 pushrod set (2) $18
2  4-bolt main bearing hsg set (2) $100
3 governor assy $20
1 cam cover w/governor & tappet $80
2 fuel pipe set (2) $40
1 hand crank $22
3 2 fuel filter assy $20
2 small stud/bolt set $10
3 valve cover bolt $8
3 main seal set (2) $15
3 rocker bushing $5
1 fuel lever $5
1 complete gasket set $15
3 head gasket $15
3 cylinder head w/valves $175

Here are a few extra new spares that I don't need. Source was either Central Maine or DES.
Crankshaft tapered roller bearings set (2) - $40 (2 sets available)
Starting crank - $20 (2 available)
Pushrod Set - $15
Camshaft - $75

One of the bearings has a little surface rust on the exterior, nothing on the bearing surfaces.

CONUS sales only. Add $18 shipping for large USPS flat rate box, $13 for medium size.
Pay with Paypal +4% or USPS money order.

When I assembled mine, I tried to use a ring compressor and slide the jug down. The tool got caught up and jammed in the chamfer at the bottom f the sleeve. I ditched the tool, and just did it with my hands, It went on just fine.

I'm the other Texan who inquired. I just couldn't justify (to my wife) $500 in fuel and three days on the road for this. If it had been just a little closer...........

How did you figure out which pulley to buy?     If I need 3600rpm at the generator and 650rpm for the engine how do I figure pulley size?     I'm sure if I take the size of my flywheel there should be a formula to get the size of pulley I need,  but I sure don't know it.

i used an online calculator and ended up with a 4.5" pulley on the generator head.