Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - doandevil

Pages: [1]
1
Engines / engine geometry
« on: September 05, 2011, 08:23:44 AM »
Dear all

does anyone here know about the Lister geometry....i need A and L in the image uploaded below desperately.......it's really diffucult to open the engine and measure all the dimensions.
Thank you

2
Engines / Re: Prechamber volume
« on: September 05, 2011, 08:13:42 AM »
mine was 75cc also....she came from India...... ;D......after comparing with you guys here i felt more confident...thx  ;D ;D ;D

3
Engines / Prechamber volume
« on: July 07, 2011, 09:51:07 AM »
Guys

I wanna do some combustion experiment and calculation heat release with Lister CS 6/1, but i don't know the volume of the prechamber....it's quite difficult to measure.....does anyone here got information or  know how to measure ?

Thanks ;D

4
Engines / Re: Lister CS 6/1 can not reach full load
« on: February 28, 2011, 09:33:27 AM »




these are the picture of my engine.........i used a dial gauge to identify the TDC and i believe there no mistake with that point. I marked on both the engine block and flywheel for timing later. Today i checked again and still hear the "knocking" noise, i was confused i don't really know where did it come from ???? ??? ??? ???

I heard the sound from somewhere in cylinder head, not in the flywheel, i am sure about this.
i opened the injector and check...there was no leak. The GIB key is alrite, still very tight. today i used a clamp meter to measure the amper in the load bank and badluck it was just 3Kw now.

I am just a newbie with Lister so there are many i still don't know. Please forgive if i ask too many question.

5
Listeroid Engines / Re: Lister CS 6/1 fuel injection pressure
« on: February 28, 2011, 08:37:17 AM »
i tried to upload some image of my engine, hope you guys can take alook at "her"



6
Listeroid Engines / Re: Lister CS 6/1 fuel injection pressure
« on: February 28, 2011, 05:55:20 AM »
my fuel pump is exactly that MICO Bosch.....and i now i don't know how to advance the injection timing.......someone told me to adjust the bolt underneah the pump....i tried but it too tight i am afraid that it will break down. I back to work now.......hopefully you guys can help me........i am still a newbie with lister and is trying to learn something.......so plz forgive me..... ;D

7
Listeroid Engines / Lister CS 6/1 fuel injection pressure
« on: February 28, 2011, 04:14:03 AM »
Hi everyone

I own one Lister CS 6/1 from India and unfortunately the user manual of the engine did not mention anything about the injection pressure. Does anyone know about this?

8
Engines / Re: Lister CS 6/1 can not reach full load
« on: February 25, 2011, 05:44:31 AM »
today i checked injection timing of my engine and it was 14 CA BTDC.........if i advance i think it will result in serious knocking.......currently my engine run not so smooth and some time knock..........what happened ????

9
Engines / Re: Lister CS 6/1 can not reach full load
« on: February 21, 2011, 05:45:58 AM »
yup.....at 3.5kw my engine becomes holy smoky......black smoke and then.....slowly shut down. It look like i have no choice but to accept this  ;D, thanks guys.

10
Engines / Lister CS 6/1 can not reach full load
« on: February 18, 2011, 09:04:25 AM »
Dear all

i own a lister CS 6/1 bought from india and currently got some problems with my engine. I coupled my engine with a generator and used bulbs to load my engine for some experiments using PPO. When i run the engine at 3.5 Kw nothing happen but when i add 1/kw more the engine became overload and automatically shut down. I tried to adjust the governor again but it's not working. Does anyone here knew about this problem before ? Please help me. Thanks a lot =(

11
Listeroid Engines / Buy new Listeroid engine
« on: May 04, 2010, 06:42:46 AM »
 Hi everyone, I am currently a student in BanDung Institute of Technology, Indonesia and I intend to work on Listeroid engine for my graduation thesis. My advisor told me to look for a buy one for my experiment. After searching on the internet i decided to buy from India but very confuse  :'(. I don t know which manufacture is the most suitable (quality of engine, price...ect....) ???. I will run the test with Jatropha crucas, coconut and palm oil (crude oid). Can you guys give me some advices. Thank you. :)

Pages: [1]