Puppeteer

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - oldtime

Pages: [1]
1
General Discussion / Lister JP3 16KVA 3 phase generator .
« on: February 21, 2022, 10:01:26 PM »
Hi all anyone got any leads on a manual for the 3 phase Generator ?
 Its all painted Army green !! It starts and runs Well . I need to sort out the Generator end . thanks Mark Canberra Australia

2
Everything else / JP Lister Fuel Drain
« on: February 21, 2022, 01:23:41 AM »
Hi all how does this water drain work ?
 Genuine lister JP3 with generator   16 KVA three phase
 I am also looking for information about the Generator end .
 It has been under a house for the last 20 odd years .
 Got it home on the weekend its Very heavy thinking above two tons .

3
Listeroid Engines / lister JP3 filter mod
« on: May 07, 2019, 11:43:11 PM »
Hi all I have seen a couple of fuel filter mods for the original Cast iron fuel filter .
 I want to know what fuel filter people are using . I can do the machining but cant find a suitable filter .
 My local filter place was a total waste of time . thanks to all

4
Listeroid Engines / ajaffa Bob OK ?
« on: May 03, 2019, 07:17:07 AM »
Hi all is Bob ok ? I have been trying to contact him . He has been in Hospital .

5
Listeroid Engines / JP3 engine dating ?
« on: April 26, 2019, 08:27:50 AM »
Hi all more questions !!!!
Engine no 60 40 255.
27 3 35 specification
Any idea when it was made . Does anyone know how to decide these numbers thanks to all

6
Listeroid Engines / Jp3 inspection !!!
« on: April 21, 2019, 07:16:16 AM »
Hi all slowly getting it to bits .  It's looking much better .. but
I have found a loose crankshaft timing gear . I did not want to take out the crankshaft but it looks like it will have to come out to fix the timing gear I suspect it will have a worn out key . Not looking forward to getting it out . I only have one shoulder that works properly .  I am thinking of remove flywheel and putting it on it's end and pulling out the crankshaft with the forklift . It's big and ugly .  What do you think about this . 

7
Listeroid Engines / Ozlisteroids.
« on: April 16, 2019, 11:08:34 AM »
Hi all I have used them a few times . A real nice guy. Is he still going ? Hope is ok . Anyone got a phone number for him .. thanks to all

8
Listeroid Engines / Jp cylinder liners
« on: April 13, 2019, 09:41:52 AM »
Hi all anyone know the difference in liners from a cs and a jp
 I can get cs liners. But not had any luck getting some for the jp . It's getting cleaner .. have the heads off . The liners might go again . There is lots of carbon . So much the valves are not seating . The ports are full .. not sure why . Time will tell
 

9
Listeroid Engines / Jp3 oil quantity
« on: April 10, 2019, 06:51:10 AM »
Hi all anyone have an idea how much oil is in a jp3 ? The industrial version ? I have found the plug near the oil pump . I am not looking forward to pulling the plug. . there looks like a big mess coming up .

10
Listeroid Engines / Hi I am new here .
« on: April 06, 2019, 03:35:32 AM »
Greetings from Australia .
Yes I have rusty metal syndrome .....
Just finished a ronaldson and tippet ck twn cylinder 27 hp diesel .. now for my next project . Lister JP3 !  It's a bit sad but will endavour to put a smile back on .  It's an industrial engine . It will require a few bits .  Liners and pistons maybe .  I am still assessing the bits .  I might c it I can use some listeroid liners but will c .  Thank God I have a machine shop . It's going to need some help . I have been scraping the oil of the outside looking for the sump plug !  Still looking . Got to there somewhere !!! Anyway back to the filth hellow to all

Pages: [1]