Puppeteer

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Fig

Pages: [1]
1
Well I tried different pics today and no luck. It keeps saying no text in message even though I had about 3 lines of text. Iím not sure whatís going on.

2
Canít seem to post jpeg pics for some reason. I got a new to me iPhone and it doesnít seem to allow changing file types from jpeg to jpg.

3
Nice running little Detroit. It has approximately 1900 + hours on it. Low oil level shutdown, air intake shutdown. Oil bath air filter.  Itís sitting on a two wheel trailer. Iíll try to get pics soon. I donít have any on my new phone. $2000 obo  located  in central Illinois.

I also have a Fairbanks Morse badged P&H 6 cylinder. Itís a big boy. Two scavenger blowers and a huge turbo on top. Very similar to the Detroit 671.  $2500

4
Listeroid Engines / Re: Students visit a "high tech " assembly plant
« on: August 15, 2019, 03:43:03 PM »
Pretty much as I imagined it. I bought one of these listeroids 15 years ago. I went to use one of the pry points on it with very slight pressure and the pry point snapped off. I immediately sold it. I kind of wish I had kept it now. They seem to have increased in value.

5
Listeroid Engines / Re: 12-2 Air over Start
« on: August 15, 2019, 03:36:45 PM »
We have some air friction motors like that at work. Ours have a small airbag that applies pressure to the motor so that the friction occurs. The bag deflated and the motor moves away from the friction point. Pretty simple process.

6
Original Lister Cs Engines / Re: Rust protection
« on: April 12, 2019, 03:12:56 PM »
Diesel coolant additive might help. It's supposed to prevent rust.

7
Did you sell it?  If not I'm interested.

8
Changfa Engines / Re: Laidong and alternative fuels
« on: April 12, 2019, 02:57:02 PM »
I just got off the phone with the chap in WI, apparently they are importing these as pellet mills. The horizontals are hooked up to a belt driven mill on a steel frame and being imported that way. How is this possible?

Here is their website: http://www.pelletmasters.com
Look under all products, pellet mills, diesel powered.



So what were their prices on the engines alone?

9
Anhydrous lanolin mixed with your favorite machine oil works pretty good for keeping rust away   ;)

10
Changfa Engines / Re: Changfa twin
« on: April 25, 2018, 11:07:23 PM »
I haven't taken any pics yet.  It is literally the generator in that first post with the YouTube link. I brought it home in a snow storm so I wrapped it in plastic and shrink-wrap.  I haven't unwrapped it yet because we have been having oddball snowstorms and i5s sitting on my porch at the moment. Hopefully this warm week we have had marks the end of the snow. I'll probably unwrap it this weekend.  I need to get a gen shed set up.

11
Changfa Engines / Re: Changfa twin
« on: April 25, 2018, 02:09:47 PM »
I just bought the one in the first post a few weeks ago.  I didn't realize twins were an oddball.  The manual was saying it can use parts from a changfa r175. It doesn't say which parts though.

12
Listeroid Engines / Re: Largest displacement listeroid single ?
« on: April 25, 2018, 01:29:11 PM »
There used to be a guy on here with what I believe was a 20 HP single, if memory serves me.  I think his handle was Dirtbikepilot or something like that.

13
Original Lister Cs Engines / Re: Newbie with oldie
« on: May 06, 2017, 01:29:13 AM »
Oops think I must have accidently locked the thread....lol.

Is this the place ?

http://diesel-electric.us

14
Hi

I have recently got a CS6 and was wondering where you got all of your parts from? Im sure ill be needing some of the same.

15
Original Lister Cs Engines / Newbie with oldie
« on: May 05, 2017, 02:36:16 PM »
Hello men,


I have been lurking in the corner for a bit. I have an old Lister CS6 that came off of a start o matic. I just have the engine, nothing else. I think i might need some bits for the governor to set it up as a stand alone and not a som. I may also need other parts as i dig into it.  I was wondering where can I find parts? What parts from a Listeroid are interchange-able? I saw a post in the classifieds where a guy had an original and he had alot of new parts for it. I hope i have as much luck. Thanks.

Fig

Pages: [1]