Puppeteer

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - saba

Pages: [1] 2 3 ... 6
1
Thanks for all the nice replies, its missing some brackets so when I speed it up the air casing is resonating and touching the flywheel. Brackets were welded to the fueltank support still need to mount them.
When you speed it up it does start to 'walk" a bit. It's an 8/1 with alluminium piston maybe that helps to keep it more ballanced. I have a 6/1 som thats really not as ballanced as this.

Greetings Bernhard

2
Listeroid Engines / Re: Foundation
« on: April 19, 2019, 10:06:11 PM »
Just an idea they sell mega blocks/ anti terror blocks, big one is 1,60 meter/0,8/0,8.  2400kg and here in holland 100 euro/120 dollar.
Had a simmilar plan like you once but changed my mind in the end. I went the flexible route.

cheaper than doing yourelf i gues

greetings bernhard

3
https://www.youtube.com/watch?v=FaV_CQf7-Ec&t=13s

Still some brackets missing, found they were on the fuel tank. Was the first run in the new location.

Bernhard

4
Original Lister Cs Engines / Re: nice video with support role cs
« on: March 13, 2019, 02:00:15 AM »
For me its the sound of the big engine, takes your breath away.

5
Original Lister Cs Engines / nice video with support role cs
« on: March 11, 2019, 11:41:32 PM »
https://www.youtube.com/watch?v=S6kUl102uxQ

Every man should have a container like this in his garden.


6
Lister Based Generators / Re: cs startomatic belts
« on: March 10, 2019, 10:58:24 PM »
Goodday you can have a look at stationary engineparts thats where I bought them. Special section SOM parts.  Greetings Bernhard

7
Changfa Engines / Re: jiang dong R108d flange/pulley
« on: February 08, 2019, 12:21:43 AM »
Thanks for the suggestion but like glort says it's to expensive to transport. Guy is asking 200 euro for the engine it's a clearout of some rent a box kind of thing. So he does not know anything about the engine. It's a 1,,5/2 hour drive for me one way that's keeping me from picking it up. Does not seem expensive to me.




8
Generators / Re: Another IMAG attempt.
« on: February 04, 2019, 10:26:40 AM »
Hey Glort it's a dahlander motor, I use it for my chp start the lister with the low rev setting when the lister is reaching it's 600 revs I kick in the high revs to feed back. It's from the days when the frequency drives were still expensive. Now they still use it to drive big fans for example.

gr Bernhard

9
Changfa Engines / jiang dong R108d flange/pulley
« on: January 31, 2019, 03:17:08 PM »
Maybe a stupid question, I was looking at a china clone that came up for sale and I am just wondering where can you get a pulley. Tried several google searches but could not find anything.

bernhard

10
Hey Bruce it was a bit late when I read your message. By the looks of it I think in the siemens s7 we have the function block diagram. There are codes and blocks with conections that don't seem to go anywhere. Now that I see your message I think I should have a look at it. I could really steel the show if I have some knowledge of it.

Node red is not a language to put in a plc, at least as far as I know, I think you can talk to it with modbus or OBD and and do a lot more with your plc.
Quick look on youtube, www.youtube.com/watch?v=fV78MQks6BI, just scroll past the install stuff and you can get an idea what you can do.

Greetings Bernhard

11
Hello bruce, I will read it and have a look at it. I like this stuff so I like some new input. Come back to you later.
Bernhard

12
Hey Bruce, the only language I "know" is C I put a lot of time and effort to master the language. At moments I came close, but after a while .... at the moment I can sort of read the code and understand what is happening, it's not so hard actually.

Mqtt is just made to send short messages or to reseave a message to do something((Message Queuing Telemetry Transport) is an ISO standard (ISO/IEC PRF 20922)[3] publish-subscribe-based messaging protocol.). Small and powerfull.  Node red can do also  someting with mqtt but it's really powerfull it's not some half ass attempt. Just google or have a look on youtube.
It's standard inside raspberry pi.

Bernhard


13
Hey Bruce I know you do not like other people's software but I am not smart enough to make something myself from scratch. There have been times I came close but after a small year most of my skills are gone again.
With the "new" esp8266 you can collect data send it wirelessly with mqtt to a broker and use node red to control all of it. Node red is also something to google. Really interesting. You can do your "coding"in there it's graphical.  Just like to encourage people to have a look, it's not hard even I can use it.

You mentioned the teensy board, I heard about it but am not familliar with it. I saw you can also program it with arduino ide.

In my job we have mostly siemens s7 plc's there is no ladder diagram inside (was made 2013). Nobody in the group has really the skills to really find what your looking for in the raw code. There is scada wich gives you access to certain things but at times you need to adjust a timer or such and most of the time it takes a day to find what you need to change where. I really don't know what they used for programming they have remote sessions to adjust/make changes.

So in short with mqtt and node red and some microcontrolers of your choosing you can make something complex dirt cheap and with very limited knowledge. Have fun.

Greetings Bernhard




14
Heavy respect to work with plc's I had a look into it when I started to get something automated, for the expenses and the diffeculty I decided to go the arduino route.

For somebody who is not into electronics and programming I would highly recoment just to have a look at it. It's really cheap and there are so many people busy with it you can just use the code from somebody else and adapt it a little to your own needs. Now there are the esp8266 boards that are super powerfull and have wifi on board and you can program it with arduino. They cost less then 4 dollar in china.

Just a message to encourage people not to get scared away when it comes to automation,

Greetings Bernhard

15
Other Slow Speed Diesels / Re: Another shop project
« on: January 15, 2019, 12:26:10 PM »
Nice project, just had a quick look on youtube,

https://www.youtube.com/watch?v=l1fd_cIVJ6A

That should be it I guess.

Bernhard

Pages: [1] 2 3 ... 6