I bought this brand new about 20 years ago. It was used for some testing and has barely been run. There is some surface rust here and there, but no pitting. Comes with the sheave and adapter plate shown. Located near downtown Houston. $750 plus shipping CONUS only.

ETA: Shipping weight is about 375# and I am very good with getting good deals on LTL shipments. So don't be afraid that shipping costs will be prohibitive.

ETA2: I found the spares, which I will include with the gen head. Lots of brushes with brush holders, both bearings, slip ring, some electronic component that I can't remember the use for, and some instructions and schematics.

Edited to change quantities of sold items.

Here is a list of the parts that go with the engine that I am selling. Almost all came from Central Maine Diesel. I will sell these parts separately, and adjust the engine price accordingly. Prices are per each except where noted + shipping at cost. I only ship to the USA. No fee payment methods: PayPal F&F, Venmo, Cryptocurrency. Payment +3% methods: PayPal G&S, credit/debit via phone.

YouTube video of parts:
https://www.youtube.com/watch?v=iLtxAADOYRg

3 con rod small end brg, std $15
4 con rod large end brg set w/shims, std $15
3 main brg, sleeve type, std $25 ea.
3 bronze idler gear $120
3 injector, Bosch, complete $70
3 injector pump, Bosch $75
4 gib key set (2) $10
1 gib key puller $50
3 injector nozzle, Bosch $30
3 pump element, Bosch $30
3 pump valve, Bosch $20
3 valve guide set (2) $12
3 valve set (2) $17
3 valve spring set (4) $13
3 rocker arm set (2) $13
1 SOLD rocker arm assy $30
3 2 tappet set $20
1 SOLD wrench set $20
4 3 banjo bolt set (2) $10
1 injector pump tappet $15
3 idler gear bolt $8
2 valve guide seal set (2) $10
2 valve cap set (2) $5
4 valve cup set (2) $5
3 piston w/ wrist pin, std. $40
3 2 piston ring set, std $20
1 cylinder block w/ liner, std. $150
2 cylinder block w/o liner $75
1 head stud set w/nuts $40
2 1 camshaft assy. w/gear $80
2 cylinder liner $75
2 pushrod set (2) $18
2  4-bolt main bearing hsg set (2) $100
3 governor assy $20
1 cam cover w/governor & tappet $80
2 fuel pipe set (2) $40
1 hand crank $22
3 2 fuel filter assy $20
2 small stud/bolt set $10
3 valve cover bolt $8
3 main seal set (2) $15
3 rocker bushing $5
1 fuel lever $5
1 complete gasket set $15
3 head gasket $15
3 cylinder head w/valves $175

Here are a few extra new spares that I don't need. Source was either Central Maine or DES.
Crankshaft tapered roller bearings set (2) - $40 (2 sets available)
Starting crank - $20 (2 available)
Pushrod Set - $15
Camshaft - $75

One of the bearings has a little surface rust on the exterior, nothing on the bearing surfaces.

CONUS sales only. Add $18 shipping for large USPS flat rate box, $13 for medium size.
Pay with Paypal +4% or USPS money order.

About 2 weeks ago, I purchased a 6/1 Indian Listeroid kit from Dieselgman. It only took a few days to arrive in Houston from Kansas City. I pulled the rod out and checked the clearance and it was .006, so I just put it back together. The only thing that I did to the crank bearings was to flush clear oil through them to remove the gunk, and I cleaned out the crankcase. It took me a couple of tries to get the piston clearance right. The lower oil ring ended up broken, as indicated by the chunk of it that I luckily spotted in the sump, so I had to tear it back down. The other issues that I had were the rocker arm alignment, and fuel tank plumbing. Gary (Dieselgman) was kind enough to send me a new oil ring, a couple of different rocker assy's, and some more plumbing items. I got it all together and fired it up today. As an extra challenge, today was the coldest day in years. Anyway, it fired up on the second try. Assisting was Ben (injin Man on Microcogen), who also bought one, but hasn't assembled his yet.

[youtube]http://www.youtube.com/watch?v=LTZSxbrQLXM[/youtube]