Puppeteer

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - occles

Pages: [1]
1
Lister Based Generators / lister sr3
« on: April 28, 2016, 02:30:13 PM »
HI, I HAVE A LISTER SR3 with a brush 10kva generator i was told it used to be a startomatic but all i have is the generator the engine starts by turning the generator ie there is no starter how many batteries will i need to start it thanks in advance

2
Lister Based Generators / hour meter on lister sr3
« on: March 28, 2012, 12:03:39 PM »
im thinking of installing an hourmeter to my lister sr3 sometimes i run it without batteries so the 24v live to the diesel pump would be no good i've seen 240v ones on ebay would i be able to connect this to the actual gen head? many thanks Richard

3
Generators / Re: sr3 starting problems again!!!
« on: February 25, 2012, 08:25:22 AM »
thanks combustor will try this

4
Generators / sr3 starting problems again!!!
« on: February 24, 2012, 11:26:07 AM »
finally started the sr3 last week via the exciter no probs went to start it again today same batteries(recharged) would not turn over voltmeter on terminals at control box show 24.1v inside control box when starter button is pushed little spring loaded thingy (solenoid?) engages but engine does not turn should i try new batts someone said even though i''ve got the volts i might not have the amps i cant start it by hand alone because as soon as i try to throw the decompressor i lose momentum can anyone help please

5
Generators / sr3 flashing?
« on: February 17, 2012, 11:31:40 AM »
Hi.got the sr3 running since yesterday as soon as it started lights id left on in shed lit up happy days turned lights off went outside turned generator off to refit exhaust started back up sweet as turned lights back on no power checked the output with meter only 15v gen head made by brush ive heard of flashing but everyone mentions diodes and rectifiers can anmyone help (idiot tems please)

6
Engines / lister sr3
« on: February 16, 2012, 11:02:30 AM »
Hi, does anybody know wheather it would be possible to fit a 12v starter motor to an sr3 to repace using the 24v dc on the brush gen head there is a blanking plate wher i assume the starter should go but not sure about ring gear many thanks

7
Generators / lister sr3
« on: September 18, 2011, 08:14:37 AM »
Hi can anyone help i am trying to wire up a lister sr3 coupled with a brush ac gen head about 10 kva inside the control box are 5 wires(all white)1 is 24v live,1 operates the throttle solenoid,1 turns the alternator.Using these 3 wires and 2 switches i can start the unit but the batteries dont charge of the 2 remaining wires 1 is showing 30 volts and the other is earth where do i connect these please help somebody

8
Lister Based Generators / lister sr3 generator
« on: March 17, 2009, 08:59:37 AM »
Hi,I have a lister sr3 with a brush 10kiva generator inside the box on top are 5 wires 1 is 24v live,1 is starter,1 is fuel pump.I've sorted these so she starts but there is1 which comes from the voltage reg which shows 33volts dc where should I connect this and 1 which appears to be an earth can someone help please?

9
Lister Based Generators / lister sr3
« on: March 04, 2009, 07:35:25 PM »
Hi,I have a lister sr3 generator whch doesnt start via the 24v system can anyone advise on a starter motor as there is a blanking plate on the side Regards Richard

10
Generators / lister sr3
« on: February 27, 2009, 08:58:50 AM »
Hi,I've just bought an sr3 with a 9.5kva brush alternator.It starts straight away on the handle and I have 240v from the box on the side the box on the top has 5 wires coming from it but no control I need to know how to start it via 24 v and how to wire it correctly for 240 startomatic not important.The box on the side has only two terminals live and earth no neutral can anyone help please (laymans terms)Regards Richard

Pages: [1]